
SPA-2XOC48POS/RPR is the Cisco Router Shared Port Adapter. This Cisco 1-, 2-, and 4-Port OC-48c/STM-16c POS/RPR SPAs are available on high-end Cisco routing platforms and offers the benefits of network scalability with lower initial costs and easy upgrades. The SPAs continues the Cisco focus on investment protection along with consistent feature support, broad interface availability, and leading-edge technology. The SPAs allow different interfaces (POS, ATM, etc.) to be deployed on the same carrier card.
SPA-2XOC48POS/RPR Specifications | |
Type | Cisco Router Shared Port Adapter |
Product Compatibility | Cisco Catalyst 6500 Series Switches |
Cisco 7600 Series Routers | |
Cisco 12000 Series Routers | |
Cisco XR 12000 Series Routers | |
Cisco ASR 1000 Series Router | |
Cisco ASR 9000 Series Router(2 port only) | |
Cisco CRS Carrier Routing System(2 and 4 port only) | |
Port Density per SPA | 1, 2, and 4 ports |
Physical Interface | OC-48c/STM-16c SFP optics module (see optical parameters below) |
Visual status indicators (LEDs) | |
• SPA status LED | |
• Per port LEDs | |
• Carrier/Alarm | |
• Active/Loopback | |
• Protect (DPT/RPR mode) | |
• Pass Through (DPT/RPR mode) | |
Protocols (see table below for RPR/SRP support info) | High-Level Data Link Control (HDLC), RFC 2615 |
Point-to-Point Protocol (PPP), RFC 1662 | |
Frame Relay, RFC 2427 | |
IPv4/IPv6 | |
IEEE 802.17 - Resilient Packet Ring (RPR) | |
IETF 2892 - Spatial Reuse Protocol (SRP) | |
Features and Functions | Synchronization |
• Local (internal) or loop timed (recovered from network) | |
• Stratum 3 clock accuracy (± 4.6 ppm) over full operating temperature | |
• Pointer activity monitoring | |
Local (diagnostic) and line (network) loopback | |
Section DCC (SDCC) - Platform-dependent feature | |
Payload mapping | |
• 1 + X^43 self-synchronous scrambler | |
SONET/SDH compliance | |
• Telecordia (Bellcore) GR-253-CORE (as applicable) | |
• ANSI T1.105, T1.231 | |
• ITU-T G.707, G.957, G.825 (as applicable) | |
Supported SONET/SDH alarm and signal events | |
• Signal Failure Bit Error Rate (SF-BER) | |
• Signal Degrade Bit Error Rate (SD-BER) | |
• Signal Label Payload Construction (C2) | |
• Path Trace Byte (J1) | |
• Section | |
• Loss of Signal (LOS) | |
• Loss of Frame (LOF) | |
• Error Counts for B1 | |
• Threshold Crossing Alarms (TCA) for B1 | |
• Line | |
• Line Alarm Indication Signal (LAIS) | |
• Line Remote Defect Indication (LRDI) | |
• Line Remote Error Indication (LREI) | |
• Error Counts for B2 | |
• Threshold Crossing Alarms (TCA) for B2 | |
• Path | |
• Path Alarm Indication Signal (PAIS) | |
• Path Remote Defect Indication (PRDI) | |
• Path Remote Error Indication (PREI) | |
• Error Counts for B3 | |
• Threshold Crossing Alarms (TCA) for B3 | |
• Loss of Pointer (LOP) | |
• Positive Stuffing Event (PSE) | |
• Negative Stuffing Event (NSE) | |
• Path Unequipped Indication Signal (PUNEQ) | |
• Path Payload Mismatch Indication Signal (PPLM) | |
Network Management | RFC 2558 MIB (SONET/SDH) |
Simple Network Management Protocol (SNMP) | |
Reliability and Availability | Online insertion and removal (OIR) |
Field-replaceable SFP optical modules | |
1+1 SONET Automatic Protection Switching (APS) and SDH Linear Multiplexer Section Protection (MSP) protocols | |
Single SPA software reset | |
Physical Specifications | Weight: 0.75 lbs (0.34 kg) |
Height: 0.8 inches (2.03 cm) | |
Width: 6.75 inches (17.15 cm) | |
Depth: 7.28 inches (18.49 cm) | |
Power | 18 Watts maximum (4-port) |
15.5 Watts maximum (1-, 2-, and 4-Port) | |
12 Watts maximum (1-port) | |
Environmental Specifications | Operating temperature: 41° to 104°F (5° to 40°C) |
Storage temperature: -38° to 150°F (-40° to 70°C) | |
Operating humidity: 5 to 85% relative humidity | |
Storage humidity: 5 to 95% relative humidity | |
Compliance and Agency Approvals | Safety |
UL 60950 | |
CSA 22.2-No.60950 | |
EN60950 | |
IEC 60950 CB Scheme | |
ACA TS001 | |
AS/NZS 3260 | |
EN60825IEC60825 laser safety (SR, IR-Class 1) (VSR-Class 1M)1 | |
21CFR1040 -FDA Code of Federal Regulations (USA) laser safety (SR, IR-Class 1) (VSR-Class 1M)1 | |
EMC | |
FCC Part 15 (CFR 47) | |
ICES 003 | |
EN55022 | |
CISPR 22 | |
AS/NZ 3548 | |
VCCI | |
EN55024 | |
EN50082-1 | |
EN61000-6-1 | |
EN61000-3-2 | |
EN61000-3-3 | |
Network Equipment Building System (NEBS) | |
This product is designed to meet the following requirements (official qualification may be in progress): | |
SR-3580 - NEBS: criteria levels (Level 3 compliant) | |
GR-63-Core - NEBS: physical protection | |
GR-1089-Core - NEBS: EMC and safety | |
European Telecommunications Standard Institute (ETSI) | |
EN300 386/EN300 386-2 Class B | |
ETS 300 019 Storage Class 1.1 | |
ETS 300 019 Transportation Class 2.3 | |
ETS 300 019 Stationary Use Class 3.1 |
The Cisco® Interface Flexibility (I-Flex) design combines shared port adapters (SPAs) and SPA interface processors (SIPs) to help enable service prioritization for voice, video, and data services. Enterprise and service provider customers can take advantage of improved slot economics resulting from modular port adapters that are interchangeable across Cisco routing platforms. The extensible Cisco I-Flex design maximizes connectivity options and offers superior service intelligence through programmable interface processors that deliver line-rate performance. Cisco I-Flex enhances speed-to-service revenue and provides a rich set of quality of service (QoS) features for premium service delivery while effectively reducing the overall cost of ownership. This data sheet contains the specifications for the Cisco 1-, 2-, and 4-Port OC-48c/STM-16c Packet over SONET/SDH (POS) and Resilient Packet Ring (RPR) Shared Port Adapter (Cisco 1-, 2-, and 4-Port OC-48c/STM-16c POS/RPR SPA; )
LonRise Equipment Co. Ltd.
The Formation of Lonrise
My Company was founded in 2007 as Cisco distributor and integrator domestically.
After 4 years' steadfast development, it spotted the business abroad. Thus Lonrise stepped on the road as a global CISCO supplier which has owned a good reputation within field .
We not only gain a continued trust from old customers but also attract many new customers.
Lonrise company structure
ABOUT US
Lonrise is specialized in supplying new original sealed Cisco equipment. Our product can create tremendous cost effectiveness for our customer. Our superior service makes our customer's purchasing process a comfortable journey. Lonrise concentrates on the construction of Cisco equipment supply Channel. We are the superior network equipment supplier and source of Cisco new equipment. We are the first choice of your Cisco product source.
Our Office in ShangHai:
Business Partners:
Awards Wall:
Lonrise Team:
Lonrise can low your cost of networking infrastructure. We supply new Cisco equipment around 65%-90% based on global list price. We endeavor to keep our price as low as possible. And meanwhile we struggles to give our best service till each details.
Lonrise supplies all new factory sealed Cisco equipment, including Cisco Routers, Cisco Switches, Cisco Firewall, Cisco module and relative Cisco software and license.
Lonrise people believe that only through creditable management and utmost service, we can win reputation for our company.